RCJones wrote:Is it possible to get surge tank dampers when the fuel tank dampers are ready? for those of us that missed the first shipment.
Thanks!
Hi, I have some tank dampers & surge tank dampers already printed, if I don't have any left I will just print to order, there really is no restriction on shipments. Just ask.
How many sets do you require?
Adrian
ZX750-E1, KLR650-A3, ZRX1100-C3, SV650-K1, Moto Morini 3 1/2 Strada
VinoBassi wrote:Nice going Adrian..Thanks for doing all this for us,Cheers plenty
Thanks, Once I use up all previously printed parts I will be able to improve the finish of the damper parts from experience over the last year & continuous printer mods. Looking at surge tank covers in PETG (basically a better material along the lines of ABS), I also have XTC-3D resin to finish printed items which can be sand & painted, did classic mini door rubber trims that came out 'perfect' but took a weekend to do thou.
If anybody does request items please supply a drawing or dimensions for me to work from as I will only remove/copy items off my own bike which are easy to get at (I wont strip my restored bike to get to parts).
ZX750-E1, KLR650-A3, ZRX1100-C3, SV650-K1, Moto Morini 3 1/2 Strada
Hi, I have been busy with other projects including designing planetary gearboxes for better prints & haven't forgotten about these covers but thay have taken a back seat for the moment. When I do copy one of my OEM covers I will need an external tester to try them out (I will put them on my bike to test anyway), issues I have thought about are strength & design of the lugs as these are a weak point, also I am going to have outside skin & no inside skin showing infill pattern etc. Do I supply "as printed" & let the customer prime & paint or do I prep, prime & satin paint at more cost? All need to be considered as its made out of plastic.
I should be able to come up with something this Xmas thou. When I have a prototype done I will post on the 3d printed parts page I have setup for my parts.
Regards,
Adrian
ZX750-E1, KLR650-A3, ZRX1100-C3, SV650-K1, Moto Morini 3 1/2 Strada
Charlie @ Evergreen wrote:Hey Adrian I need to order more dampers for the waste gates if you have any available??? let me know.
Thanks man
Charlie
Hi Charlie, I wasn't sure how well they were doing in the field.
I can print however many you require, I still have a few from the last batch available. Let me know numbers.
Regards
Adrian
ZX750-E1, KLR650-A3, ZRX1100-C3, SV650-K1, Moto Morini 3 1/2 Strada
Any luck with the surge tank covers?[/quote]
Hi, Here is an update on the surge tank covers as far as I have got. The bottom mounts need to be modelled & will be a weak point that I will try & strengthen as these are plastic & not pressed steel.
Here are some initial models for left & right that I need to prototype print & measure up to my bike to make sure they look the part & fit correctly.
ZX750-E1, KLR650-A3, ZRX1100-C3, SV650-K1, Moto Morini 3 1/2 Strada
TurboRestorer wrote:Any luck with the surge tank covers?
Hi, Here is an update on the surge tank covers as far as I have got. The bottom mounts need to be modelled & will be a weak point that I will try & strengthen as these are plastic & not pressed steel.
Here are some initial models for left & right that I need to prototype print & measure up to my bike to make sure they look the part & fit correctly.
ST Cover L.jpg
ST Cover R.jpg
[/quote]
84 750E1 ,zx7 swing arm & rim , Zr7s shock ,dyna coils, k&n , bov , afpr , variable resistor for race mode. Ported spider ,dump pipe , Evergreen billet HT-10 , RTI hydraulic clutch .
PLEASE DO NOT USE THIS THREAD FOR 3D PRINTED PARTS, PLEASE GOTO '3D PRINTED REPLICA ITEMS' THREAD INSTEAD AS THIS CONTAINS PRICING & OEM PART NUMBERS. 