HT10B Turbocharger Specs & Pics

Turbocharger repairs, alternative options and mods
User avatar
Charlie @ Evergreen
Intercooler
Posts: 6986
Joined: Sun Nov 17, 2013 12:20 am
Location: Ocala, Florida USA

Re: HT10B Turbocharger Specs & Pics

Post by Charlie @ Evergreen »

Grinding HT10 Turbine Shaft undersize .005
Attachments
VIDEO HT TWS.jpg
VIDEO HT TWS.jpg (26.79 KiB) Viewed 1107 times
84' ZX750 Turbo 85'ZX750 Turbo
User avatar
Charlie @ Evergreen
Intercooler
Posts: 6986
Joined: Sun Nov 17, 2013 12:20 am
Location: Ocala, Florida USA

Re: HT10B Turbocharger Specs & Pics

Post by Charlie @ Evergreen »

3 of Peter Reilly's HT10s built.
Two are HT10s machined up and upgraded billet compressor
One is HT10/TC03 Mitsubishi Cartridge upgrade from UK rebuild and blueprinted with same GT20 Billet Compressor Wheel
Turbine Housing on #1 needed all 4 bolt holes repaired.
Turbine Housing replaced on #2 as it had no turbine housing and waste gate actuator.
Turbine Housing on #3 had two broken bolts and one egg shaped bolt hole repaired. All three got surfaced flat on both flanges.
Bearing Housings Line Bored/ Turbine Shafts grind on the two HT10s/Mitsubishi is STD.
So far looking good to get them all built as got a $1 wager I can do it! :humour

Two to go! :thumbup
Attachments
HT BILLET 2.jpg
HT BILLET 2.jpg (22.6 KiB) Viewed 1078 times
HT BILLET 3.jpg
HT BILLET 3.jpg (24.06 KiB) Viewed 1078 times
HT  TC 1.jpg
HT TC 1.jpg (24.29 KiB) Viewed 1078 times
HT  TC  2.jpg
HT TC 2.jpg (27.34 KiB) Viewed 1078 times
HT BILLET 3.jpg
HT BILLET 3.jpg (24.06 KiB) Viewed 1078 times
PETER HTs.jpg
PETER HTs.jpg (31.97 KiB) Viewed 1078 times
84' ZX750 Turbo 85'ZX750 Turbo
User avatar
Charlie @ Evergreen
Intercooler
Posts: 6986
Joined: Sun Nov 17, 2013 12:20 am
Location: Ocala, Florida USA

Re: HT10B Turbocharger Specs & Pics

Post by Charlie @ Evergreen »

On to Peter's #4 turbo build and more challenges.

Turbo been built before so had some interesting mods done.
So did the following machining get specs in over under size bearings seals

Bearing Housing Seal area plus .010
Bearing Housing Line Bored plus .010
Thrust Collar Seal opened plus .010
Turbine Shaft Grind minus .005
Seal Plate opened Seal Area plus .010
Compressor Housing was machined snap ring groove deeper for some reason so replaced.
Attachments
HT 4  TH.jpg
HT 4 TH.jpg (23.05 KiB) Viewed 1000 times
HT 4 TH 2.jpg
HT 4 TH 2.jpg (25.45 KiB) Viewed 1000 times
HT  5.jpg
HT 5.jpg (25.88 KiB) Viewed 1000 times
HT 6.jpg
HT 6.jpg (22.37 KiB) Viewed 1000 times
HT 7.jpg
HT 7.jpg (22.04 KiB) Viewed 1000 times
HT 8.jpg
HT 8.jpg (32.62 KiB) Viewed 1000 times
84' ZX750 Turbo 85'ZX750 Turbo
User avatar
Charlie @ Evergreen
Intercooler
Posts: 6986
Joined: Sun Nov 17, 2013 12:20 am
Location: Ocala, Florida USA

Re: HT10B Turbocharger Specs & Pics

Post by Charlie @ Evergreen »

Peter's 5 Hitachi order Billet upgrades & set of Bosch Injectors cleaned flowed ready to ship
Attachments
Ht10s.jpg
Ht10s.jpg (100.12 KiB) Viewed 944 times
HT10s & Injectors.jpg
HT10s & Injectors.jpg (102.42 KiB) Viewed 944 times
84' ZX750 Turbo 85'ZX750 Turbo
ickyoldman
Member
Posts: 22
Joined: Sun Jan 05, 2020 10:52 pm
Location: Richmond, IL

Re: HT10B Turbocharger Specs & Pics

Post by ickyoldman »

Just beautiful Charlie!
User avatar
Charlie @ Evergreen
Intercooler
Posts: 6986
Joined: Sun Nov 17, 2013 12:20 am
Location: Ocala, Florida USA

Re: HT10B Turbocharger Specs & Pics

Post by Charlie @ Evergreen »

Like flying the Intruder D!
84' ZX750 Turbo 85'ZX750 Turbo
User avatar
Charlie @ Evergreen
Intercooler
Posts: 6986
Joined: Sun Nov 17, 2013 12:20 am
Location: Ocala, Florida USA

Re: HT10B Turbocharger Specs & Pics

Post by Charlie @ Evergreen »

Gonk's turbo/basket and injectors
Clutch basket dampers were shot. Turbo needed grind turbine journal .005/ bearing housing line bored .005
Replaced turbine housing/compressor wheel.

Ready to go and make some boost.
Attachments
dampers  6 15.jpg
dampers 6 15.jpg (31.46 KiB) Viewed 605 times
HT 1.jpg
HT 1.jpg (30.67 KiB) Viewed 605 times
HT2.jpg
HT2.jpg (22.14 KiB) Viewed 605 times
HT3.jpg
HT3.jpg (15.87 KiB) Viewed 605 times
HT4.jpg
HT4.jpg (25.78 KiB) Viewed 605 times
HT105.jpg
HT105.jpg (32.62 KiB) Viewed 605 times
84' ZX750 Turbo 85'ZX750 Turbo
User avatar
Charlie @ Evergreen
Intercooler
Posts: 6986
Joined: Sun Nov 17, 2013 12:20 am
Location: Ocala, Florida USA

Re: HT10B Turbocharger Specs & Pics

Post by Charlie @ Evergreen »

Gonks final pics
Attachments
HT10 10.jpg
HT10 10.jpg (26.78 KiB) Viewed 602 times
HT10 11.jpg
HT10 11.jpg (28.74 KiB) Viewed 602 times
HT10 12.jpg
HT10 12.jpg (25.82 KiB) Viewed 602 times
84' ZX750 Turbo 85'ZX750 Turbo
Olcockie
Supporter
Posts: 24
Joined: Thu Aug 20, 2020 7:38 am
Location: Western Australia

Re: HT10B Turbocharger Specs & Pics

Post by Olcockie »

Another one on its way Charlie. :thumbup . Looking forward to seeing the magic :rock

OC
ZX750 E1
GPz900r A7 (Plan B) :oops:
GPz900r (Plan C)
User avatar
Charlie @ Evergreen
Intercooler
Posts: 6986
Joined: Sun Nov 17, 2013 12:20 am
Location: Ocala, Florida USA

Re: HT10B Turbocharger Specs & Pics

Post by Charlie @ Evergreen »

Wade's Billet HT10 & new check valve line installed. 1st one using jig. Will also be getting all the component parts to make complete new lines in a week. Option to make new lines to replace if one is leaking or prefer the new design will post up. RC injector clean and flowed then installed the new hose ends with crimp locks.
Attachments
WADE 1.jpg
WADE 1.jpg (25.31 KiB) Viewed 185 times
WADE 2.jpg
WADE 2.jpg (26.07 KiB) Viewed 185 times
WADE4.jpg
WADE4.jpg (28.02 KiB) Viewed 185 times
WADE5.jpg
WADE5.jpg (25.84 KiB) Viewed 185 times
WADE 3.jpg
WADE 3.jpg (26.57 KiB) Viewed 185 times
84' ZX750 Turbo 85'ZX750 Turbo
User avatar
Charlie @ Evergreen
Intercooler
Posts: 6986
Joined: Sun Nov 17, 2013 12:20 am
Location: Ocala, Florida USA

Re: HT10B Turbocharger Specs & Pics

Post by Charlie @ Evergreen »

Jessie's HT10 Billet Upgrade with new check valve line installed.
Machined up for .005-.010 Journal Bearings get specs in. Seals good in STD.
Attachments
HT10 Billet.jpg
HT10 Billet.jpg (29.87 KiB) Viewed 64 times
Billet comp set.jpg
Billet comp set.jpg (25.9 KiB) Viewed 64 times
HT Seal plate.jpg
HT Seal plate.jpg (17.74 KiB) Viewed 64 times
HT10 Billet.jpg
HT10 Billet.jpg (29.87 KiB) Viewed 64 times
HT10 Turbine.jpg
HT10 Turbine.jpg (28.74 KiB) Viewed 64 times
HT10 turbine side.jpg
HT10 turbine side.jpg (26.82 KiB) Viewed 64 times
HT 10 grind 010.jpg
HT 10 grind 010.jpg (23.08 KiB) Viewed 64 times
HT with valve.jpg
HT with valve.jpg (29.8 KiB) Viewed 64 times
84' ZX750 Turbo 85'ZX750 Turbo
User avatar
Charlie @ Evergreen
Intercooler
Posts: 6986
Joined: Sun Nov 17, 2013 12:20 am
Location: Ocala, Florida USA

Re: HT10B Turbocharger Specs & Pics

Post by Charlie @ Evergreen »

Lot of HT10s come in pretty rough there not many in good condition.

Thought show few pics from Rod in AU
Attachments
AU UGLY.jpg
AU UGLY.jpg (26.03 KiB) Viewed 16 times
AU UGLY 2.jpg
AU UGLY 2.jpg (18.98 KiB) Viewed 16 times
84' ZX750 Turbo 85'ZX750 Turbo
Post Reply