Search found 265 matches

by rangeroy
Fri Nov 06, 2026 4:15 pm
Forum: For Sale/Wanted
Topic: Plenum covers
Replies: 8
Views: 394

Re: Plenum covers

£40 pair unpainted and £70 pair painted
by rangeroy
Wed Nov 04, 2026 7:47 pm
Forum: Maintenance & Restoration
Topic: FUEL TANK HARDWARE
Replies: 9
Views: 2112

Re: FUEL TANK HARDWARE

with regard to z1300 tap there are 2 types,1 for the fuel inected bikes & 1 for the early carb versions which have a vaccum tap , my error for not giving correct advice :cry
by rangeroy
Tue Nov 03, 2026 4:18 pm
Forum: For Sale/Wanted
Topic: Plenum covers
Replies: 8
Views: 394

Re: Plenum covers

Adrian prints them (turbo restorer) :thumbup
by rangeroy
Sat Oct 31, 2026 8:18 pm
Forum: Maintenance & Restoration
Topic: FUEL TANK HARDWARE
Replies: 9
Views: 2112

Re: FUEL TANK HARDWARE

:rock :thumbup :beer :victory
by rangeroy
Wed Sep 30, 2026 7:06 pm
Forum: General discussion
Topic: Wanted To Buy See Pic
Replies: 5
Views: 716

Re: Wanted To Buy See Pic

okee dokee, I would have no issue fitting pickups with this part number 59026-1026, I have a set of these pickups that a mate is using on a gpz1240 motor but if you want I could get them back for a test on my turbo if you are not sure, I have used them on a Z650 with standard engine & N/A gpz 750 ...
by rangeroy
Mon Sep 28, 2026 7:20 pm
Forum: General discussion
Topic: Head/Valve Cover Broken Bolt Ear
Replies: 3
Views: 401

Re: Head/Valve Cover Broken Bolt Ear

Devcon plastic steel putty maybe? if your alu rods dont work :popcorn
by rangeroy
Mon Sep 28, 2026 7:15 pm
Forum: General discussion
Topic: Wanted To Buy See Pic
Replies: 5
Views: 716

Re: Wanted To Buy See Pic

There are probably igniters from a couple of models that will do if you cannot sort yours, normal gpz750 springs to mind but dont discount gpz600r or even gpz900 & gpz1100 :thumbup
by rangeroy
Sat Sep 26, 2026 6:36 pm
Forum: General discussion
Topic: Projects Update. Turbo Rebuild
Replies: 2
Views: 360

Re: Projects Update. Turbo Rebuild

Nice vid about valve clearance & good shout out for Adrian's 3D parts :thumbup its the way I check valve lash exept I included the number 3 exhaust & number 2 inlet when i do number 4 inlet/exhaust, turn motor over to do number 1 inlet/exhaust then do number 3 inlet & number 2 exhaust at same time ...
by rangeroy
Mon Sep 21, 2026 6:50 am
Forum: General discussion
Topic: Low Compression Update 9/21/26
Replies: 14
Views: 1131

Re: Low Compression

As kawadoodle says throttle bodies fully open and I bet your problem will be solved :thumbup
by rangeroy
Sun Sep 20, 2026 8:05 pm
Forum: General discussion
Topic: Low Compression Update 9/21/26
Replies: 14
Views: 1131

Re: Low Compression

cam timing fine (just looked again on youtube vid you posted) use kawadoodle oil trick or leak down tester as Horsh said.
good luck :thumbup :thumbup
by rangeroy
Mon Sep 14, 2026 9:16 am
Forum: Maintenance & Restoration
Topic: Wetting plugs and poor idle....
Replies: 12
Views: 1425

Re: Wetting plugs and poor idle....

race mode enabled? :popcorn
by rangeroy
Mon Sep 07, 2026 6:27 am
Forum: General discussion
Topic: Valve and Cam Timing EUREKA!!!
Replies: 4
Views: 536

Re: Valve and Cam Timing

Exhaust cam first,then inlet, don't get too wound up over exactly lining marks to cylinder head it's the pin count that's important
by rangeroy
Sat Jul 18, 2026 2:13 pm
Forum: Maintenance & Restoration
Topic: Wetting plugs and poor idle....
Replies: 12
Views: 1425

Re: Wetting plugs and poor idle....

Jez will be correct over the relief valve if it sticks it will increase pressure & fuelling, not sure why the injectors didnt fit the cleaning rig? seems odd to me & they could be bigger than the normal 240cc as standard so if you have spares try them :thumbup
by rangeroy
Thu Jul 16, 2026 7:16 pm
Forum: Maintenance & Restoration
Topic: Wetting plugs and poor idle....
Replies: 12
Views: 1425

Re: Wetting plugs and poor idle....

plugs too cold use 8's whilst its on the stand, its not producing boost so no chance of damage (IMHO) when you had injectors cleaned did you have them flowed/cc'ed & are they standard?
good luck :thumbup